在镇江地区从事铝艺大门、安全防护栏研发、设计、生产、安装一条龙服务

中华彩票网

中华彩票网官网 > 中华彩票网注册 > 时事新闻

中华彩票网官网?

2019-06-22 11:10:04 扬中市乐夫装饰材料经营 阅读

平刀是环氧地坪漆施工过程中用到的重要工具,在批刮中涂砂浆层和腻子层以及刮涂面漆时都会用到,但是在施工过程中因为一些原因导致环氧地坪施工后表面存在刮刀痕的现象,严重影响了环氧地坪工程的美观性。那么是什么原因导致环氧地坪漆表面出现刮刀痕呢?如何避免呢?

Flat knife is an important tool used in the construction of epoxy floor paint. It is used in batch scraping to coat mortar layer, putty layer and scraping paint. However, there are scratch marks on the surface of the epoxy floor after construction due to some reasons, which seriously affects the aesthetics of the epoxy floor project. So what causes scratch marks on the surface of epoxy floor paint? How to avoid them?导致环氧地坪漆表面出现刮刀痕原因:

Causes of scratch marks on the surface of epoxy floor paint:

1、环氧地坪施工人员操作手法有问题,即持刀不平,造成每两次批刮之间形成深浅不一的接茬。

1. There are some problems in the operation of epoxy floor constructors, i.e. uneven knife holding, resulting in different depth of stubble between each batch scraping.

2、环氧地坪漆涂料的施工黏度过高,而稀释剂的挥发速度又太快。

2. The application viscosity of epoxy floor paint is too high, and the volatilization rate of diluent is too fast.

3、环氧环氧地坪漆涂料混进水分,使颜料粒子在油水界面凝絮,降低了涂料的流动性。

3. Moisture is mixed into epoxy floor paint, which makes pigment particles flocculate at oil-water interface and reduces the fluidity of the paint.

4、一次倒料过多。镘刮施工环氧地坪漆时,需要先将涂料倒在地面上,再用镘刀镘刮开来。当涂料倾倒过多,要刮很久才能用完,但地坪漆涂料的流平性却越来越差,最终无法自动流平,产生刀痕。

4. Overfeeding at one time. When scraping floor paint, it is necessary to pour the paint on the ground first, and then scrape it with a trowel. When the paint is overdumped, it takes a long time to scrape out, but the leveling of the floor paint is getting worse and worse, and eventually it can not leveling automatically, resulting in knife marks.

5、反复去收平。施工环氧地坪漆时要干净利落,不能反复去收平,刮了几遍都没刮好,回头刮了一次又一次,否则也会出现刀痕问题。

5. Repeatedly leveling off. When constructing epoxy floor paint, it should be clean and neat. It can not be collected repeatedly, scraped several times without scraping well, and scraped again and again. Otherwise, there will be knife marks.

6、批刮中涂砂浆层后没有进行充分打磨。

6. After batch scraping, the mortar layer was not fully polished. 避免环氧地坪表面施工后出现刮刀痕的方法:

Method of avoiding scratch marks on the surface of epoxy floor after construction:

1、环氧地坪漆施工一定要选择经验丰富的施工工人,专业的施工技术是做出优质环氧地坪工程的前提。

1. The construction of epoxy floor paint must select experienced construction workers. Professional construction technology is the premise of making high-quality epoxy floor paint.

2、环氧地坪漆施工时要避免黏度过高,可以通过添加配套的稀释剂来调整环氧地坪涂料的黏度。

2. In order to avoid excessive viscosity in the construction of epoxy floor coatings, the viscosity of epoxy floor coatings can be adjusted by adding matching diluents.

3、环氧地坪漆是油性材料,一定要避免水分的进入,一旦进入水分要使用滤纸吸除后再使用。

3. Epoxy floor paint is an oily material. It must avoid water entering. Once water enters, it must be absorbed by filter paper before it is used.

4、环氧地坪漆施工时单次配料不宜过多,并且每次倒料也不宜偏多。

4. Epoxy floor paint construction should not be too much of a single ingredient, and each pour should not be too much.

5、环氧地坪漆刮涂施工时切忌反复去收平,刮涂施工时要干净利落。

5. When scraping and painting epoxy floor paint, do not take it back again and again. When scraping and painting, it should be clean and neat.

6、每批刮完一遍中涂砂浆干燥后都需要精细打磨吸尘,目的就是去掉表面的颗粒和痕迹,同时再跟进批刮一遍或两遍腻子,填补砂浆层留下的凹陷部位。

6. After each batch is scraped once and the mortar is dried, it needs fine polishing and dust absorption. The purpose is to remove the particles and traces on the surface, and then follow up with the batch scraping once or twice putty to fill the depression left by the mortar layer.



标签:   铝艺大门 环氧地坪 铝艺护栏 铝艺大门厂家